DreamTurboCard (Spanish)

From Enterprise Wiki
Jump to: navigation, search
Dream Turbo Card (etapa de diseño)

Breve información

Dream Turbo Card (DTC) es una placa de expansión interna que añade memoria RAM y FlashROM, reloj de tiempo real(RTC) y generador seleccionable de reloj de sistema y EXDOS.

Especificaciones

  • 1 MB de SRAM, opcionalmente 2 MB, en bancos de 64KB,
  • 512 KB de FlashROM, 8 bancos de 64 KB con opción de desactivación individual con EXOS siempre en el banco 7,
  • RTC reloj,
  • NVRAM (alimentada por bateria),
  • Generador de señal de reloj de dos canales sincronizados:
    • Reloj de sistema 4/8/12/16/20 MHz (2/4/6/8/10 MHz Z80 CPU),
    • Reloj de EXDOS 8/9.6/10/12/13.33/16 MHz,
  • Pantalla LCD u OLED (2x16 caracteres),
  • LED RGB para señalar por colores la frecuencia de CPU seleccionada:
    • 2MHz azul,
    • 4MHz verde,
    • 6MHz amarillo,
    • 8MHz naranja,
    • 10MHz rojo,
  • Opcionalmente sensor de temperatura para NICK,
  • Configurable por codificador rotatorio o por software.

Caracteristicas

Comunicación con la tarjeta

Dirección I/O Sentido Contenido
0x7E escritura Selección de dirección NVRAM
lectura registro de estado de la tarjeta
0x7F escritura datos NVRAM
lectura

Registro de estado

Bit Nombre Contenido
0 EP RFSH el microcontrolador ha modificado la memoria NVRAM (el EP debería comprobarlo, y la lectura del puerto de datos NVRAM pondrá a cero este bit)
1 CLK Sys Ready el reloj de Sistema se ha sincronizado con el ajuste actual
2 CLK EXDOS Ready el reloj EXDOS se ha sincronizado con el ajuste actual
3 RTC RQ el microcontrolador de la tarjeta ha solicitado el acceso a la memoria NVRAM
4 RTC RFSH el EP gravó datos en la memoria NVRAM (la lectura por el microcontrolador pondrá a cero este bit)
5 reserved por ahora siempre '0'
6 S0 bit de estado 0 del microcontrolador (1 = lectura de temperatura completada)
7 S1 bit de estado 1 del microcontrolador (por ahora sin uso)

Config registers

Address Bits Content
NVRAM CPLD 7 6 5 4 3 2 1 0
0x7F *) NA Device ID Dream Turbo Card ID is 44h
0x7E *) NA Hw batch no. Hw serial no. Hardware serial number
0x7D *) NA Hw ver. mj. Hw ver. mn. Hardware version (major.minor)
0x7C *) NA Fw ver. mj. Fw ver. mn. Firmware version (major.minor)
0x7B *) NA DSP LS RAM2 uC TEMP Flash Features (below)
0x7A 3 Memory mode EXDOS clock select System clock select Memory bank mode, selection of clocks (below)
0x79 2 CLK link Flash.6 Flash.5 Flash.4 Flash.3 Flash.2 Flash.1 Flash.0 Disabling flash memory banks, bit N=1 Flash bank N disable
0x78 *) 1 S1 S0 LCD bias uC status bits & LCD contrast
0x77 *) 0 LCD backlight LED blue LED green LED red LCD backlight and RGB LED control
0x76 *) NA Current temperature Current NICK temperature
0x75 NA Temperature limit NICK temperature level for the alarm (0 = alarm off)

*) read-only, data will be always overwritten by the card microcontroller,

Feature Description Value Type
Flash Flash chip type 00 Microchip SST39SF040
01 .
10 .
11 .
TEMP temperature sensor type 00 none
01 Dallas DS18B20
10 Analog Devices TMP03/04
11 Analog Devices TMP05/06
uC microcontroller type 0 MCS51
1 AVR
RAM2 RAM capacity 0 1 MB
1 2 MB
LS sound transducer 0 buzzer or none
1 loudspeaker
DSP display type 0 OLED
1 LCD

Memory map

MT is MICROTEAM card.

Mode 0 (default)
BANK x0-x3 x4-x7 x8-xB xC-xF
0x Flash.7 CART EPNET EPNET
1x MT SRAM1 MT SRAM1 MT SRAM1 MT SRAM1
2x MT Flash MT Flash MT Flash MT Flash
3x MT SRAM2 MT SRAM2 MT SRAM2 MT SRAM2
4x MT DRAM1 MT DRAM1 MT DRAM1 MT DRAM1
5x MT DRAM2 MT DRAM2 MT DRAM2 MT DRAM2
6x Flash.0 Flash.1 Flash.2 Flash.3
7x Flash.4 Flash.5 Flash.6 RAM1.F
8x RAM2.0 RAM2.1 RAM2.2 RAM2.3
9x RAM2.4 RAM2.5 RAM2.6 RAM2.7
Ax RAM2.8 RAM2.9 RAM2.A RAM2.B
Bx RAM2.C RAM2.D RAM2.E RAM2.F
Cx RAM1.0 RAM1.1 RAM1.2 RAM1.3
Dx RAM1.4 RAM1.5 RAM1.6 RAM1.7
Ex RAM1.8 RAM1.9 RAM1.A RAM1.B
Fx RAM1.C RAM1.D RAM1.E VRAM
Mode 1 (no RAM2)
BANK x0-x3 x4-x7 x8-xB xC-xF
0x Flash.7 CART EPNET EPNET
1x MT SRAM1 MT SRAM1 MT SRAM1 MT SRAM1
2x MT Flash MT Flash MT Flash MT Flash
3x MT SRAM2 MT SRAM2 MT SRAM2 MT SRAM2
4x MT DRAM1 MT DRAM1 MT DRAM1 MT DRAM1
5x MT DRAM2 MT DRAM2 MT DRAM2 MT DRAM2
6x Flash.0 Flash.1 Flash.2 Flash.3
7x Flash.4 Flash.5 Flash.6 RAM1.F
8x not used not used not used not used
9x MT SRAM1 MT SRAM1 MT SRAM1 MT SRAM1
Ax MT Flash MT Flash MT Flash MT Flash
Bx MT SRAM2 MT SRAM2 MT SRAM2 MT SRAM2
Cx RAM1.0 RAM1.1 RAM1.2 RAM1.3
Dx RAM1.4 RAM1.5 RAM1.6 RAM1.7
Ex RAM1.8 RAM1.9 RAM1.A RAM1.B
Fx RAM1.C RAM1.D RAM1.E VRAM
Mode 2 (no Flash)
BANK x0-x3 x4-x7 x8-xB xC-xF
0x Flash.7 CART EPNET EPNET
1x MT SRAM1 MT SRAM1 MT SRAM1 MT SRAM1
2x MT Flash MT Flash MT Flash MT Flash
3x MT SRAM2 MT SRAM2 MT SRAM2 MT SRAM2
4x MT DRAM1 MT DRAM1 MT DRAM1 MT DRAM1
5x MT DRAM2 MT DRAM2 MT DRAM2 MT DRAM2
6x RAM2.8 RAM2.9 RAM2.A RAM2.B
7x RAM2.C RAM2.D RAM2.E RAM1.F
8x RAM2.0 RAM2.1 RAM2.2 RAM2.3
9x MT SRAM1 MT SRAM1 MT SRAM1 MT SRAM1
Ax MT Flash MT Flash MT Flash MT Flash
Bx MT SRAM2 MT SRAM2 MT SRAM2 MT SRAM2
Cx RAM1.0 RAM1.1 RAM1.2 RAM1.3
Dx RAM1.4 RAM1.5 RAM1.6 RAM1.7
Ex RAM1.8 RAM1.9 RAM1.A RAM1.B
Fx RAM1.C RAM1.D RAM1.E VRAM
Mode 3 (no Flash & RAM2)
BANK x0-x3 x4-x7 x8-xB xC-xF
0x Flash.7 CART EPNET EPNET
1x MT SRAM1 MT SRAM1 MT SRAM1 MT SRAM1
2x MT Flash MT Flash MT Flash MT Flash
3x MT SRAM2 MT SRAM2 MT SRAM2 MT SRAM2
4x MT DRAM1 MT DRAM1 MT DRAM1 MT DRAM1
5x MT DRAM2 MT DRAM2 MT DRAM2 MT DRAM2
6x not used not used not used not used
7x not used not used not used RAM1.F
8x not used not used not used not used
9x MT SRAM1 MT SRAM1 MT SRAM1 MT SRAM1
Ax MT Flash MT Flash MT Flash MT Flash
Bx MT SRAM2 MT SRAM2 MT SRAM2 MT SRAM2
Cx RAM1.0 RAM1.1 RAM1.2 RAM1.3
Dx RAM1.4 RAM1.5 RAM1.6 RAM1.7
Ex RAM1.8 RAM1.9 RAM1.A RAM1.B
Fx RAM1.C RAM1.D RAM1.E VRAM

Clock selection

SELECT System clock CPU clock EXDOS clock
0 8 MHz 4 MHz 8 MHz
1 12 MHz 6 MHz 9.6 MHz
2 16 MHz 8 MHz 10 MHz
3 20 MHz 10 MHz 12 MHz
4 4 MHz 2 MHz 13.33 MHz
5 8 MHz 4 MHz 16 MHz
6 8 MHz 4 MHz 8 MHz
7 8 MHz 4 MHz 8 MHz

Minimum value of system clock in "linked mode"

When we raise the EXDOS clock frequency, the data from the FDC controller will be sent faster.
In some cases, the processor clocked by a lower frequency may not be able to process transmitted data.
To prevent this situation, it is possible to activate the "linking" mode of clock signals.
In this mode the card's microcontroller will ensure that the processor's clock frequency is not less than the minimum frequency at which the processor is able to keep pace with data from the FDC controller.

Selected system clock 4 MHz 8 MHz 12 MHz 16 MHz 20 MHz
Selected EXDOS clock Actual frequency (System/CPU)
8 MHz 8 MHz 4 MHz 8 MHz 4 MHz 12 MHz 6 MHz 16 MHz 8 MHz 20 MHz 10 MHz
9.6 MHz 8 MHz 4 MHz 8 MHz 4 MHz 12 MHz 6 MHz 16 MHz 8 MHz 20 MHz 10 MHz
10 MHz 8 MHz 4 MHz 8 MHz 4 MHz 12 MHz 6 MHz 16 MHz 8 MHz 20 MHz 10 MHz
12 MHz 12 MHz 6 MHz 12 MHz 6 MHz 12 MHz 6 MHz 16 MHz 8 MHz 20 MHz 10 MHz
13.33 MHz 12 MHz 6 MHz 12 MHz 6 MHz 12 MHz 6 MHz 16 MHz 8 MHz 20 MHz 10 MHz
16 MHz 16 MHz 8 MHz 16 MHz 8 MHz 16 MHz 8 MHz 16 MHz 8 MHz 20 MHz 10 MHz

How to install

DTC is a complex interface. The installation requires interference with the computer.
The author has made every effort to make the interface as reliable and safe to use as possible. However,

You make any modifications inside of your equipment at your own risk !

What you need

  • Dream Turbo Card
  • L-connector
  • new Z80 processor suitable for work at clock speeds of at least 10 MHz (eg. Z84C0010P, Z84C0020P)

Enterprise mainboard preparation

  • desolder and remove internal 64KB RAM memory module (Enterprise 128 only)
  • desolder the Z80 processor

Instalación del conector L

Primera puesta en marcha

Enlaces

Hilo en el foro Enterprise Forever 6Mhz and more...

Manual en otros lenguajes

Inglés

Polaco

Alemán

Húngaro